Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Miami Homeowners
A gate that won’t open, drags on the track, or makes a grinding sound at 7 a.m. needs a specialist, not a generalist. Daystar Gate Repair fixes automatic and manual gates across Miami every day, from single-family driveways in Coral Gables to commercial entry systems in Brownsville. We carry parts and diagnostic tools for nine major gate brands, which means we show up already knowing what commonly fails on your unit. Rene Castellano built this company on single-trade focus. Gates are all we work on. If your gate is stuck, noisy, or refusing to close, call (855) 752-6802 for a straight answer and a free estimate.
Driveway Gate Repair
Driveway Gate Repair means getting your automatic or manual entry gate operating smoothly again, whether it’s a swing arm, a slide track, or a vertical pivot. In Miami’s salt air and summer storms, we see track corrosion, hinge sag, and motor failures more than anywhere else. Daystar repairs the gate itself, the operator, and the safety system as one unit. A typical driveway gate repair in Miami runs $180 to $450 for mechanical fixes, while operator and control board work can reach $600 to $1,200 depending on the brand, so it helps to understand Gate Repair pricing before you call. We quote the full price before any work begins, so there are no surprises on the invoice.
Operator Diagnostics and Repair
Most driveway gate failures stem from the operator, not the gate leaf. We test limit switches, capacitor health, and gear wear on brands like Ghost Controls and Mighty Mule, then repair or replace the motor as needed. Rene Castellano’s technicians don’t swap parts blindly; they confirm the root cause first.
Hinge, Wheel, and Track Service
Steel gates sag over time, and Miami’s humidity accelerates rust at the hinge points. We rebuild hinges, replace bearing wheels, and re-level slide tracks so the gate moves without dragging. A sagging gate puts extra strain on the motor, so we address alignment before it becomes an operator failure.
Styles & brands we work with
Gate Welding
Gate Welding repairs the structural metal of your gate when bolts and brackets are no longer enough. Cracked welds, snapped hinges, bent pickets, and rusted-through frame members all require a welder who understands gate geometry. Daystar performs on-site welding and fabrication to restore the frame’s original load-bearing strength. Expect to pay $150 to $400 for a simple crack repair or hinge re-weld, while frame reconstruction and picket replacement can run $400 to $900 depending on material thickness and the extent of the damage. The price is agreed before the welder strikes an arc.
Crack and Break Repair
Stress cracks form where the gate leaf meets the hinge plate, especially on heavy iron gates that get opened dozens of times a day. We grind out the crack, weld it properly, and reinforce the area with gusset plates when the design calls for it. A properly re-welded gate will outlast a bolted patch by years.
Frame Straightening and Reinforcement
When a vehicle bumps a gate or a hurricane-force gust twists the frame, the gate may still function but carry hidden stress fractures. Daystar straightens the frame using controlled heat and jigs, then re-welds and braces weak points. This is structural work, and getting it wrong means the gate eventually breaks at the weld line again.
Commercial Gate Repair
Commercial Gate Repair covers the sliding, swing, and barrier gates that protect apartment complexes, industrial lots, and gated communities across Miami-Dade. These gates cycle hundreds of times a day, so component wear is dramatically faster than a residential gate. Daystar handles the gate, the operator, loop detectors, and safety sensors as one integrated system. Commercial gate repair in Miami typically runs $350 to $1,200 for standard mechanical and control board work, and our Complete Gate Repair Guide for Miami Homeowners explains what drives those costs. Heavier jobs involving vehicle barriers or custom control panels can exceed $2,000. We provide property managers with a written scope and price before scheduling any work.
High-Cycle Wear Components
Commercial gates wear out wheels, rollers, chains, and drive gears at a rate residential gates never see. We stock industrial-grade replacement parts for DoorKing and Elite operators, the two most common brands in Miami’s commercial properties. Preventive replacement of a worn drive chain costs far less than the downtime and repair bills from a snapped one.
Access Control Integration
Many commercial gate failures are actually access control failures. A keypad, telephone entry system, or card reader that stops triggering the operator will make the gate appear broken. Daystar diagnoses the whole signal path from entry device to the control board, so we fix the actual fault instead of replacing a healthy motor.
Iron Gate Repair
Iron Gate Repair addresses the structural and mechanical problems specific to heavy ornamental iron gates, both manual and automated. Miami’s coastal air attacks iron aggressively, creating rust pockets at joints, hinge plates, and decorative scroll points. Daystar repairs, reinforces, and repaints iron gates to stop corrosion from spreading through the frame. Basic rust repair and hinge work runs $200 to $450, while full restoration including media prep, welding, and repainting can run $600 to $1,500 depending on gate size and finish. We quote the job before work starts.
Rust and Corrosion Treatment
Surface rust on an iron gate is cosmetic. Deep rust at weld joints and base plates is structural. We grind affected areas down to clean metal, weld any thin spots, and apply a rust-inhibiting primer before paint. Left untreated, corrosion at the bottom rail will eventually separate the gate from its hinges.
Decorative Element Repair
Scrolls, finials, and lattice patterns break when kids climb on them or when a lawn crew hits the gate with equipment. Daystar fabricates and welds replacement pieces to match the original profile, then blends the finish. A broken decorative element is also a safety hazard, sharp edges can cut anyone who brushes against the gate.
Sliding Gate Repair
Sliding Gate Repair covers the cantilever and V-track sliding gates common at Miami commercial properties and larger residential driveways. These gates depend on precisely aligned rollers, a straight track, and a healthy drive motor. When alignment drifts, the gate grinds, shakes, and eventually burns out the operator. Daystar resets tracks, replaces roller assemblies, and tunes the motor’s torque limits for smooth starts and stops. Sliding gate repair in Miami averages $250 to $650 for roller and track work, with operator repair adding $400 to $900. We confirm the complete price before beginning.
Track Alignment and Roller Replacement
A sliding gate that bounces or shudders as it moves is telling you the rollers are shot or the track has settled out of level. Miami’s sandy soil shifts more than you’d expect, especially after heavy rain. We re-level the track, replace worn bearing rollers, and set the gate’s travel limits so it doesn’t slam at the end of its run.
Cantilever System Repair
Cantilever sliding gates ride on rollers without a ground track, which is ideal for keeping sand and debris out of the mechanism. But when the counterweight frame bends or the carriage rollers wear unevenly, the gate drags. We rebuild the carriage assembly and true the counterweight frame to factory specifications, often on Mighty Mule and LiftMaster cantilever systems.
Wrought Iron Gate Repair
Wrought Iron Gate Repair focuses on the classic ornamental gates that define so many Miami entryways, from Coral Gables estates to Miami Shores homes. True wrought iron is increasingly rare; most Miami gates are mild steel shaped to look traditional. Both require skilled welding and careful paint matching. Daystar repairs broken scrolls, re-welds hinge barrels, and restores the finish so the repair disappears into the original design. Budget $200 to $500 for typical weld repairs and hinge work. Full restoration, including stripping, priming, and repainting, runs $700 to $1,800 based on gate size and condition. We agree on the price before any torch lights up.
Traditional Hinge Repair
Hand-forged hinge barrels on wrought iron gates wear oval over decades of use, causing the gate to drop and bind. We rebuild or replace the barrel and pin, then re-hang the gate to swing true. This is precise work, and doing it wrong means the gate never lines up with the latch again.
Finish Matching and Repainting
After welding on an ornamental gate, the heat burns off the paint around the repair area. We match the existing finish, whether it’s matte black, rust patina, or a custom color, and blend it into the surrounding surface. The goal is a repair you can’t find afterward unless we point it out.
Metal Gate Repair
Metal Gate Repair covers steel and aluminum gates of every style, from simple chain-link gate frames to custom aluminum driveway gates. Aluminum doesn’t rust, but it fatigues at welds and bends easily on impact. Steel is stronger but demands active rust management. Daystar repairs both, and we know which filler and technique each metal requires. Minor repairs like hinge replacement or latch alignment run $150 to $350. More involved work, including panel replacement or frame section re-welding, runs $350 to $800. We provide a fixed quote before beginning, same as every job we take.
Aluminum Gate Repair
Aluminum gates are lightweight, which makes them popular for residential use, but the welds are prone to fatigue cracking over years of movement. We TIG-weld the cracked joints back to full strength and reinforce the area if the design keeps failing in the same spot. Patching aluminum with a steel bracket just creates a galvanic corrosion point in Miami’s humid air.
Steel Frame Repair
Steel gates bend when hit, and bent gates bind on their hinges or tracks. We use controlled heat and jigs to pull the frame back to square, then weld any cracks the bending opened up. If the damage is too extensive, we’ll tell you honestly and quote a replacement section instead of layering patch on patch.
Wood Gate Repair
Wood Gate Repair restores the function of solid wood driveway and garden gates, which fail differently than metal. Wood swells in Miami’s humidity, rots at ground contact, and splits around hardware. Daystar replaces rotted rails, re-secures hinges, and re-squares sagging frames. Most wood gate repairs in Miami run $150 to $400, depending on how much of the frame needs replacing. Full frame reconstruction on a large double gate can reach $600. We price the work upfront and stick to that number.
Rot Replacement and Frame Rebuild
The bottom rail and hinge-side stile of a wood gate absorb water from rain splatter and humidity, and that’s where rot starts. We cut out the soft wood, scarf in new pressure-treated or cedar sections, and re-mortise the hinges. Rebuilding a gate frame is usually cheaper and keeps the original character better than replacing the entire gate.
Hardware and Alignment
Loose screws, sagging hinges, and warped boards pull a wood gate out of square until the latch no longer lines up. We re-drill stripped hardware holes with epoxy-filled pilots, replace worn strap hinges, and add anti-sag cabling to keep the gate square. A wooden gate that closes properly lasts years longer than one left dragging against the post.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
Daystar Gate Repair is factory-familiar with nine gate brands, which matters when your operator fails and you need a fast fix, and our guide on Choosing the Right Gate Repair Brand explains why that expertise saves you time. On a Ghost Controls system, we know the common limit switch failures and the exact reset sequence. On DoorKing commercial operators, we’re familiar with the relay logic and the loop detector integration quirks. On Elite slide gate systems, we know how to diagnose VFD faults without swapping good parts. On Mighty Mule residential units, we know the control board symptoms that often get misdiagnosed as motor failure.
Rene Castellano’s technicians arrive with brand-specific diagnostic knowledge, not a trial-and-error mentality. That means fewer return trips, faster fixes, and parts that actually match your system. Whether you have a Ghost Controls driveway arm in Coconut Grove or a DoorKing commercial barrier in West Little River, we know your gate, and we also offer Brownsville Gate Repair for properties in that area. From Mighty Mule to FAAC, gate specialists, not generalists.
Signs You Need a Pro Right Now
- Grinding or squealing during operation. The drive gear or belt may be stripping against the motor shaft. Running it another week usually turns a $200 gear replacement into a $700 operator replacement.
- The gate reverses after closing. Safety sensors or the loop detector may be misaligned, but it could also be a failing control board. A gate that won’t stay closed is a security gap, especially on commercial properties.
- Visible sag at the hinge side. The gate has dropped, which means the hinge barrel or post is failing. Opening and closing a sagging gate flexes every weld until something cracks.
- The motor runs but the gate doesn’t move. The coupling between motor and drive shaft may be sheared, or the drive chain has slipped. This is a mechanical failure that won’t fix itself, and continuing to run the motor burns out the windings.
- The gate is stuck in the open or closed position. A completely unresponsive gate usually means a control board fault, a tripped thermal overload, or a broken limit switch. Daystar diagnoses the exact failure rather than replacing your whole operator.
Our Process, Step by Step
- 1
You call and describe the problem. We ask specific questions about your gate’s behavior, brand, and when the failure started. Rene Castellano’s team uses that information to select the right diagnostic tools and likely parts before we even leave the shop. A 10-minute phone call saves us both an hour on site.
- 2
A technician arrives and performs a full-system diagnostic. We test the mechanical components first, hinges, rollers, track, and frame alignment, because those failures cause most operator damage. Then we test the electrical system, including voltage at the board, limit switch function, and safety sensor signal. We identify the root cause, not just the symptom.
- 3
We present a fixed price before any work begins. You get a written scope of repair with the cost of parts and labor, itemized. We don’t start drilling or wrenching until you approve the number. That price doesn’t change unless we find hidden damage inside a component, and even then we call you before proceeding.
- 4
We complete the repair and test the gate through full cycles. After the mechanical and electrical work is done, we run the gate open and close repeatedly. We check force settings, limit accuracy, and safety reversal on automatic gates. The gate isn’t done until it operates smoothly and safely, with no grinding, hesitation, or drift.
- 5
We walk you through the repair and tell you what to watch for. You’ll know exactly what was fixed, what was replaced, and why it failed in the first place. If there’s a maintenance step that will extend the life of the repair, we’ll tell you. And you’ll have our phone number for any follow-up questions.
How Much Does Gate Repair Cost in Miami?
A typical gate repair in Miami runs $180 to $450 for mechanical work like hinge replacement, track alignment, or latch repair. Electric operator repairs, including control boards and motors, range from $400 to $1,100 depending on the brand and whether parts are needed. Welding and structural frame work on iron or steel gates typically lands between $200 and $800. Full gate restoration or major commercial repairs can run higher, and we’ll quote every job before starting.
Several factors affect the final number: the gate’s material and weight, the brand of the operator, the age of the system, and whether parts need to be ordered or are on the truck. We stock common parts for Ghost Controls, DoorKing, Elite, and Mighty Mule, which saves time and freight costs. We don’t charge diagnostic fees that get buried in the repair price. Our estimates are free, and the quote you approve is the quote you pay. Call (855) 752-6802 for a straight answer and an exact number.
Our Service Area Near Miami
Daystar Gate Repair serves Miami and the surrounding neighborhoods from Allapattah to Miami Beach. We regularly work in Brownsville, Gladeview, North Bay Village, El Portal, Coconut Grove, Key Biscayne, Coral Gables, Miami Shores, and West Little River. Most residential repair calls are reached within one business day, and we offer emergency service for gates stuck open or blocking access. Wherever you are in the Miami area, we know your gate. Call for current scheduling availability in your neighborhood.
Serving Miami, FL — Our Local Coverage Area
We’re based in the Miami area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Miami
Gate repair means restoring a damaged or malfunctioning gate to proper function, including the frame, hinges, wheels, track, operator, and safety systems. It covers mechanical repairs like welding and alignment as well as electrical repairs like control board replacement. Rene Castellano’s team at Daystar handles the full range, from driveway swing gates to commercial sliding systems. We fix both the gate itself and the automation that drives it.
Most residential gate repairs are completed the same day we arrive, typically within two to three hours. More involved work like full frame welding or operator replacement may take half a day. If a specialized part needs to be ordered, the job is usually finished within two to three business days. We’ll give you a realistic timeline before starting.
Basic mechanical repairs average $180 to $450, electric operator work runs $400 to $1,100, and welding or structural repairs land between $200 and $800. We quote the exact price before any work starts, so you’ll never face a surprise charge. Call (855) 752-6802 for a free estimate tailored to your gate and its problem.
Yes, we service all four brands, along with LiftMaster, FAAC, BFT, Linear, and Viking. Our technicians are factory-familiar with each brand’s known failure points and reset procedures. That means we arrive prepared to diagnose your specific system rather than learning it on your clock. Brand-specific expertise is one reason property managers keep calling us back.
We offer emergency service for security and access issues, like a gate stuck open at a commercial property or a driveway gate that won’t close at night. Same-day scheduling is available for most residential calls in the Miami area. Call as early as possible to get on the schedule, and we’ll tell you when a technician can reach your property.
Every repair carries a workmanship warranty, and the parts we install are covered by the manufacturer’s warranty. The specific term depends on the part and the repair, and we’ll state it clearly before you approve any work. If something we fixed fails under warranty, we come back and make it right. That’s been our standard since day one.
Clear the area around the gate so our technician has room to work, and have your gate’s remote or keypad available for testing. If the gate is part of a gated community, alert the front desk or property manager. Keep pets inside while the gate is being cycled and tested. Everything else, including tools, parts, and diagnostic equipment, arrives with us.
Schedule Your Gate Repair Service in Miami Today
Your gate is the first line of security for your home or property. When it fails, you need a specialist who can fix it fast and fix it right. Rene Castellano and the Daystar Gate Repair team are ready to diagnose your gate, quote the repair, and get you back to normal operation. Call (855) 752-6802 now for a free, no-obligation estimate.
Written by Rene Castellano, Owner at Daystar Gate Repair, serving Miami homeowners and property managers with dedicated gate expertise.